MOBILE PHONE DEAD PROBLEM AND SOLUTION

Mobile Phone Dead Problem and Solution 
This chapter explains Mobile Phone Dead Problem and Solution –How to Repair a Dead Mobile Cell Phone. These problem and solution apply to all brands and make of Android Smartphone or Feature Mobile Phone including Nokia, SAMSUNG, iPhone, China Mobile Phones, Motorola, HTC, Sony, Blackberry, Alcatel, Apple, AudioVox, Benefone, Danger, FIC, Hagenuk, Palm, Kyocera, LG, Xiaomi, Huawei, Oppo, Panasonic, Huawei, ZTE, Spice, Lava, Sony Ericsson, Micromax etc.


What is a Dead Mobile Phone?

A Dead Mobile Phone is a Cell Phone that does not get switched ON. It won’t turn ON and won’t Charge.

How Does a Mobile Cell Phone Gets Dead?

A mobile phone can get Dead for several reasons:
  1. If the mobile phone gets dropped down on the floor or on some hard surface.
  2. If the MOBILE PHONE GETS WET or is dropped in rain or water.
  3. If there is any kind of short ( in + and – ) or shorting in the MOBILE PHONE PCB.

Mobile Phone Dead Problem and Solution – How to Repair a Dead Mobile Cell Phone

  1. Remove the battery and see if it gets charged or not. Check voltage USING A MULTIMETER. Voltage must be 3.7-4.2 Volt DC. Use a BATTERY BOOSTER to Boost the Power of the Battery and Charge it again.
  2. Check Battery Point and Battery Connector. CLEAN BATTERY POINT AND BATTERY CONNECTER to remove any carbon deposits.
  3. Resold or change the Battery Connector.
  4. Insert charger and se if the “Battery Charging” appears or not. If there is icon of “Battery Charging” but the mobile phone does not gets switched ON then check ON / OFF Switch. Voltage of ON / OFF Switch must be 2.5 to 3.5 Volt (DC). Clean or change the ON / OFF Switch. Check track of ON / OFF Switch and JUMPER if required.
  5. If the charging icon is not there then check voltage of ON / OFF Switch. If the voltage is between 2.5 to 3.7 Volts DC, then RELOAD Software in the Phone (Software Flashing).
  6. If the phone won’t get switched ON even after reloading software then Heat the C.P.U, Power IC and Flash IC.
  7. If there is no voltage on the ON / OFF Switch then check track of the ON / OFF Switch. Jumper if required.
  8. If the problem is not solved then heat, Reball or change the Power IC and CPU to fix the problem.
  9. Keep the Multimeter on Buzzer Mode and Check + and – of the Battery Connector. If there is Buzzer Sound then the Phone is short. If there is short at the Battery Connector then clean the PCB with thinner. Apply Flux and Heat the PCB.
  10. If this does not fix the Mobile Phone Dead problem then remove the PFO and check for short. If there is short then replace the PFO.
  11. Remove the charging connector and check for shorting. If there is short then change the connector.
  12. Remove the charging IC and check for shorting. Change if required.
  13. Remove the Bluetooth IC and check for shorting. Replace if required.
  14. Remove the Power IC and check for shorting. Replace with a new one if required.
  15. Remove the CPU and check for shorting. Replace if required.
  16. Remove all the Big Electrolytic CAPACITORS and check one by one. Replace capacitors if required.

    17. Important Note

    • Some mobile phone gets dead if the RTC (Real Time Clock) is faulty. This happens mostly in China Mobile Phones. Change the RTC to fix the problem.
    • If the mobile phone gets hang after reloading software then change the RTC.
    • If the phone is still dead then check by replacing the 26 MHz Crystal Oscillator.

Comments

Post a Comment

Popular posts from this blog

Image
Five Simple Tips to Increase the Life of Your Phone's Battery    Properly charging your smartphone is essential for maintaining the health of your battery, and ensuring better battery life and increased safety in the long run. Simply plugging your phone in as soon as you get home and leaving the charger on until you leave in the morning is not the right solution. Since there is a lot of different advice floating around on how to charge your phone, we decided to get you tips to get the most out of your smartphone's battery from the guys who built. Here's what they told us: 1. Don't let your phone overheat Heat is perhaps the worst enemy of lithium-ion batteries, the kind most smartphones use. "You should take basic precautions like not keeping your phone on the dash board of the car where it will get a lot of direct sunlight," You should also avoid charging your phone while playing graphically intensive games, because that will also raise the temperatur...
Read more

SCIENCE.

Image
BLACK HOLE MYSTERY DATING BACK 40 YEARS SOLVED BY "BEST EVER" SIMULATION  A team of astrophysicists from Northwestern University, Oxford University, and the University of Amsterdam, used graphical processing units to crunch large sets of data and simulate how black holes interact with their accretion disks. The first photo of a black hole was captured in APRIL this YEAR PARIS: Scientists on Thursday unveiled the most detailed simulation of a black hole yet, solving a mystery dating back more than four decades over how the star-devouring monsters consume matter Coming fresh on the heels of the first ever photo of one of the giant objects, which are scattered across the Universe, astrophysicists are now several steps closer to understanding how they form and develop. A black hole is born when a large star collapses in on itself. Far from being a "hole", they are instead incredibly dense objects with a gravitational pull so strong that nothing, not even lig...
Read more

MOBILE PHONE AND THEIR ELECTRONIC COMPONENTS FUNCTIONS

Image
Small Parts / Electronic Components of Mobile Phone and Their  Function                               The PCB of a mobile cell phone has several small parts or electronic components. When LEARNING MOBILE REPAIRING , it is important to learn and understand how to identity these small parts or electronic components and understand their function. Identification of these small parts on the PCB OF MOBILE PHONE is easy if you know and understand some of the basic rules. It is also important to understand what to do if any of these small components is faulty. Most of these electronic components are SMD  ( SURFACE MOUNT DEVICES) They don’t have any leads like thru-hole ELECTRONIC COMPONENTS .                                                            ...
Read more